Windows 2000 Server
Your network consists of Windows 2000 file servers, Windows 2000 print servers, Windows 2000 professional computers, Windows 2000 file servers. You must prevent any unsigned drivers from being installed on any computer in your Windows 2000 network. What should you do?

Configure the Windows 2000 file servers, Windows 2000 print servers, Windows 2000 professional computers and Windows 2000 file servers to block unsigned drivers
Configure a Group policy for the Default Domain Controller to block all unsigned drivers
Do nothing, this is the default setting
Configure a Group policy for the Domain that blocks all unsigned drivers
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You have just configured two Windows NT Servers, Monitor 1 and Monitor 2 with no other software installed. You have an application server that needs to be monitored for performance to figure out what it's problem is, or to get some kind of baseline. You install Network Monitor on Monitor 2. What would you do to monitor Application server?

Configure the network monitor ECP port something for TCP
Configure Monitor 2 and Application server as monitoring partners (or something) to monitor the performance
Install Network Monitor on Application Server
Install Network Monitor on Monitor 1
Configure the network monitor EDP port something for UDP

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

Configure a client computer to use only TCP/IP for the connections to the remote access server
Configure the client computer to use a defined IPX network address for the connection to the remote access servers
Configure the remote access server to disable multi-link connection
None of above
Configure the remote access server to allow IPX based remote access demand dial connections

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
Configure the remote access server to act as a DHCP Relay Agent
Configure the remote access server with the address of a DHCP server
Authorize the remote access server to receive multiple addresses from a DHCP server
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install your boot volume on volume C on your Windows 2000 Server computer. You mirror volume C on dynamic Disk 1. Two years later, during routine server maintenance, you open Disk Management and find that the status of volume C is Failed Redundancy. The status of Disk 1 is Missing. You attempt to reactivate Disk 1, but the status of volume C does not return to Healthy. What should you do next?

Remove the mirror on Disk 1, replace the disk, and then add back the mirror to the new Disk 1
Replace Disk 1 and copy all data from volume C to a new NTFS primary partition on the new Disk 1. Restart the computer
Rescan the disks, remove the mirror, and delete the data on Disk 1. Then re-create the mirror
None of above
Replace Disk 1 and restart the computer. The mirror will automatically regenerate

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install a new multiple-process database application named Application on your Windows 2000 Server computer. Two days later, users begin to report that the new application has suddenly stopped responding to queries. You verify that the server is operation and decide that you need to restart the application. What should you do before you restart the application?

End the Application.exe process tree
None of above
End both the Explorer.exe process and the Application.exe process
End the task named Application
End the Application.exe process

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server