Windows 2000 Server
You are the administrator of Windows 2000 Server computer. Your computer has a span volume that consists of areas on three physical hard disks on the server. The three disks support hot swapping. You regularly backup the span volume by using windows backup. One of the disk fail, you replace the disk with a new un-partitioned disk. You want to recover the span volume and disk data as soon as possible. What should you do?

Extend the span volume to include the new disk, rescan the disk
Re scan the disk, extend the span volume to include the new disk. Shut down and restart the server, use windows backup to restore the new data
Re scan the disk, remove the span volume and create a new span volume that includes the new disk. Format the span volume, use Windows back up to restore the data
Re scan the disk, format the span volume. Use windows back up to restore the data
Extend the span volume to include the new disk, shut down and restart the server, use windows backup to restore the data

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 domain and TWO Windows NT domains. The Windows 2000 domains trust each of the Windows NT domains. Each of Windows NT domains trust the Windows 2000 domain. A Windows 2000 domain controller named DC1 is configured to use a highly secure domain controller template. Users in the Windows NT domain report that they cannot access DC1. You need to allow the users of computers in the Windows NT domain to access resources on DC1. What should you do?

None of above
Ensure the Windows 2000 domain is configured to run in the native mode
Apply a less restrictive custom policy to Windows NT domain controller
Apply a less restrictive custom security template to DC1
Ensure the Windows 2000 domain is configured in the mixed mode

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server with the address of a DHCP server
None of above
Authorize the remote access server to receive multiple addresses from a DHCP server
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
Configure the remote access server to act as a DHCP Relay Agent

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has FIVE hard disks. Four 100 GB hard disks on the server are configured as a single stripe volume. You want to reconfigure the fourth disk so that the volume is fault tolerant and has as much space possible available for storing data. You want to use only existing hardware. What should you do?

None of above
Convert the disk to dynamic disk shut doWn and restart the server
Backup the data on the stripe volume and delete the stripe volume. Create a mirror volume, shut down and restart the server. Restore the data to new mirror volumes
Backup the data on the stripe volume and delete the stripe
Backup the data on the stripe volume and delete the stripe volume. Create a raidS volume on the four disks, restore the data to the new raid5 volume

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Use Device Manager to change the IRQ for the original modem to IRQ 10
Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices
None Of above
Use Device Manager to change the IRQ for the original modem to IRQ 9
Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install a new multiple-process database application named Application on your Windows 2000 Server computer. Two days later, users begin to report that the new application has suddenly stopped responding to queries. You verify that the server is operation and decide that you need to restart the application. What should you do before you restart the application?

End the Application.exe process tree
None of above
End both the Explorer.exe process and the Application.exe process
End the task named Application
End the Application.exe process

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server