Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
Authorize the remote access server to receive multiple addresses from a DHCP server
None of above
Configure the remote access server to act as a DHCP Relay Agent
Configure the remote access server with the address of a DHCP server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 server Computer contains data files that users of client computers access throughout the day. You install a driver for the new tape drive on the computer. After restarting the computer you log on as an administrator, shortly after you log on you receive the following stop error "irql_not_less_6r_equal". You need to bring the server back on line as quickly and reliably as possible. What should you do?

Perform an emergency repair and select fast repair, restart the computer
None of above
Restart the computer by using the last known good menu option
Restart the computer in the safe mode, remove the driver and restart the computer
Restart the computer by using the recovery console, disable the driver. Restart the computer, remove the driver

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are configuring a Windows 2000 Server computer as a Routing and Remote Access server for a Branch office. You discover that an incorrect driver was installed during the installation of the modem. You attempt to remove the modem by using Phone and Modem Options in Control Panel. After each attempt to remove the modem by using this method, the computer stops responding. You restart the computer again. You must install the correct driver for the modem as quickly as possible. What should you do?

Run the Modem troubleshooter and remove the modem when prompted. Restart the server
Use the Add/Remove Hardware wizard to uninstall the modem. Restart the server
Shut down the server, remove the modem card, and restart the server. Shut down the server again, insert the modem card, and restart the server
None of above
Delete all references to modems in the registry

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network contains 10 domain controllers, 10 member servers, and approximately 1,000 client computers. All the servers run Windows 2000 Server, and all the client computers run Windows 2000 Professional. Two of the domain controllers act as DNS servers. Users of client computers use file sharing to grant access to files stored locally. The network has 10 subnets and uses TCP/IP as the only network protocol. You want to configure the network so that all computers can resolve the addresses of all other computers by using DNS. Client computers must be able to register and resolve addresses if a server fails. How should you configure the DNS servers?

Configure one server with a standard primary zone for the domain, and configure at least one server with an Active Directory integrated primary zone
Configure at least two servers with Active Directory integrated primary zones for the domain
Configure one server with an Active directory integrated primary zone for the domain, and configure at least one server with a standard secondary zone
Configure at least two servers with standard primary zones for the domain
Configure one server with a standard primary zone for the domain, and configure at least one server with standard secondary zone

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 domain and TWO Windows NT domains. The Windows 2000 domains trust each of the Windows NT domains. Each of Windows NT domains trust the Windows 2000 domain. A Windows 2000 domain controller named DC1 is configured to use a highly secure domain controller template. Users in the Windows NT domain report that they cannot access DC1. You need to allow the users of computers in the Windows NT domain to access resources on DC1. What should you do?

Apply a less restrictive custom policy to Windows NT domain controller
None of above
Apply a less restrictive custom security template to DC1
Ensure the Windows 2000 domain is configured in the mixed mode
Ensure the Windows 2000 domain is configured to run in the native mode

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer. You configure the server to audit all access to files that are places in shared folders. One week after you configured the server, users report that the server has stopped responding. You investigate the problem and discover a stop error with the error message: Stop C0000244 (Audit Failed) An attempt to generate a security audit failed. You restart the computer. You need to ensure that you can keep a record of all files access on the server. You also need to ensure that the stop error will not occur again.

Delete the Liscense Trial registry key
Increase the size of the security log
Set the CrashonAuditFail registry key to 0
Set the Security Log to overwrite events as needed
Save the security log to a file, and clear it every morning

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server