Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has one hard disk. This computer runs a custom application that writes a large number of small temporary files in a single directory to support request from client computers. To improve performance of the application, you add three new 100-GB SCSI disks to the server to hold these temporary files. You want to ensure that the application can use all 300 GB of space with a single drive letter. You also want to ensure the fastest possible performance when writing the temporary files. How should you configure the three disks?

Convert all three disks to dynamic disks. Create a striped volume
Convert all three disks to dynamic disks. Create a RAID-5 volume
Create a single volume on each of the three disks. Format each volume as NTFS. Mount the roots of Disk 2 and Disk 3 in the root folder of Disk 1
None of above
Create a single volume on Disk 1. Format the volume as NTFS. Extend the volume to create a spanned volume that includes the space on all three disks

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You configure your Windows 2000 Server as a print server. You install a second PnP Network adapter to improve the performance. The first adapter uses IRQ11, and the second adapter uses IRQ5. The server is now unable to print to print devices connected to a non-PnP LPT2 port adapter. You want to continue to use the print devices connected to your print server. What should you do?

Edit the CMOS setting of the servers BIOS to reserve IRQ7 for non-PnP devices
Use device manager to change the IRQ for LPT1 to IRQ10
Edit the CMOS setting of the servers BIOS to reserve IRQ5 for non-PnP devices
None of above
Use device manager to change the IRQ for LPT2 to IRQ7

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are configuring a Windows 2000 Server computer as a Routing and Remote Access server for a Branch office. You discover that an incorrect driver was installed during the installation of the modem. You attempt to remove the modem by using Phone and Modem Options in Control Panel. After each attempt to remove the modem by using this method, the computer stops responding. You restart the computer again. You must install the correct driver for the modem as quickly as possible. What should you do?

Run the Modem troubleshooter and remove the modem when prompted. Restart the server
None of above
Delete all references to modems in the registry
Shut down the server, remove the modem card, and restart the server. Shut down the server again, insert the modem card, and restart the server
Use the Add/Remove Hardware wizard to uninstall the modem. Restart the server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

Configure the remote access server to disable multi-link connection
Configure the client computer to use a defined IPX network address for the connection to the remote access servers
Configure the remote access server to allow IPX based remote access demand dial connections
None of above
Configure a client computer to use only TCP/IP for the connections to the remote access server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install your boot volume on volume C on your Windows 2000 Server computer. You mirror volume C on dynamic Disk 1. Two years later, during routine server maintenance, you open Disk Management and find that the status of volume C is Failed Redundancy. The status of Disk 1 is Missing. You attempt to reactivate Disk 1, but the status of volume C does not return to Healthy. What should you do next?

Rescan the disks, remove the mirror, and delete the data on Disk 1. Then re-create the mirror
Replace Disk 1 and copy all data from volume C to a new NTFS primary partition on the new Disk 1. Restart the computer
Replace Disk 1 and restart the computer. The mirror will automatically regenerate
Remove the mirror on Disk 1, replace the disk, and then add back the mirror to the new Disk 1
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network consists of Windows 2000 file servers, Windows 2000 print servers, Windows 2000 professional computers, Windows 2000 file servers. You must prevent any unsigned drivers from being installed on any computer in your Windows 2000 network. What should you do?

Configure the Windows 2000 file servers, Windows 2000 print servers, Windows 2000 professional computers and Windows 2000 file servers to block unsigned drivers
Configure a Group policy for the Domain that blocks all unsigned drivers
Do nothing, this is the default setting
Configure a Group policy for the Default Domain Controller to block all unsigned drivers
None of above

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server