Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
Use Device Manager to change the IRQ for the original modem to IRQ 10
None Of above
Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices
Use Device Manager to change the IRQ for the original modem to IRQ 9

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are configuring a Windows 2000 Server computer as a Routing and Remote Access server for a Branch office. You discover that an incorrect driver was installed during the installation of the modem. You attempt to remove the modem by using Phone and Modem Options in Control Panel. After each attempt to remove the modem by using this method, the computer stops responding. You restart the computer again. You must install the correct driver for the modem as quickly as possible. What should you do?

Run the Modem troubleshooter and remove the modem when prompted. Restart the server
None of above
Use the Add/Remove Hardware wizard to uninstall the modem. Restart the server
Shut down the server, remove the modem card, and restart the server. Shut down the server again, insert the modem card, and restart the server
Delete all references to modems in the registry

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server network that runs in mixed mode. You install a new Windows 2000 Server computer. You create and share a new HP LaserJet 4L printer. Your Windows 2000 Professional client computers can print to the new printer successfully. However, when users try to connect to the printer from Windows NT Workstation 4.0 client computers, they receive the dialog box shown in the exhibit. "The server on which the printer resides does not have a suitable HP LaserJet printer driver installed". You want the printer driver to be installed automatically on the Windows NT Workstation computers. What should you do?

Copy the Windows NT 4.0 printer drivers to the WinntSystem32 pri liter sdri vers folder on the Windows 2000 print server
None of above
Change the sharing options on the printer to install additional drivers for Windows NT 4.0 or Windows 2000
Copy the Windows NT 4.0 Printer Drivers to the Net logon shared folders on all Windows NT Server 4.0 computers still configured as BDCs
Copy the Windows NT 4.0 printer drivers to the Net logon shared folder on the PDC emulator

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server with the address of a DHCP server
Authorize the remote access server to receive multiple addresses from a DHCP server
None of above
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
Configure the remote access server to act as a DHCP Relay Agent

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 domain and TWO Windows NT domains. The Windows 2000 domains trust each of the Windows NT domains. Each of Windows NT domains trust the Windows 2000 domain. A Windows 2000 domain controller named DC1 is configured to use a highly secure domain controller template. Users in the Windows NT domain report that they cannot access DC1. You need to allow the users of computers in the Windows NT domain to access resources on DC1. What should you do?

Apply a less restrictive custom policy to Windows NT domain controller
None of above
Apply a less restrictive custom security template to DC1
Ensure the Windows 2000 domain is configured to run in the native mode
Ensure the Windows 2000 domain is configured in the mixed mode

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You enable the Routing and Remote Access Service (RRAS) on a computer running Windows 2000 Server. You configure the computer as a RAS server. You want to provide mutual authentication between the RAS server and RAS clients. You also want to ensure that data passing between the RAS server and RAS clients is encrypted. Which authentication method should you use for your incoming connections to support mutual authentication and data encryption?

PAP
CHAP
MS-CHAP v2
SPAP
None of above

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server