Windows 2000 Server
Your network contains NetWare 4.0 Servers. You have successfully installed Client Service for NetWare on Windows 2000 Professional computers, and Gateway Service for NetWare on Windows 2000 Server Computers. You recently added a new Windows 2000 Server computer to the network and installed Gateway Service for NetWare on it. However, the server is unable to connect to any NetWare servers. What should you do on the new Windows 2000 Server computer to resolve this problem?

Install RIP routing for IPX
Configure the NWLink IPX/SPX/ NetBIOS Compatible Transport Protocol to use the correct Ethernet frame type
Install the SAP Agent
None of above.
Enable NWLink NetBIOS

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer contains a stripe set with parity on a four-disk array. You convert the stripe set with parity to a dynamic RAID-5 volume. Six months later, users report that disk access on the server is slower than it had been on the previous day, You use Disk Management and discover that the status of the third disk in the array is Missing. You want to recover the failed RAID-5 volume. What should you do first?

Ensure that the third disk is attached to the server and has power. Use Disk Management to reactivate the disk
Install a new disk and create a single extended partition on the new disk. Restart the computer and allow Windows 2000 to automatically repair the volume on the extended partition
None of above
Ensure that the third disk is attached to the server and has power. Use Disk Management to repair the volume
Replace the third disk and restart the server. Use disk Management to repair the volume

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

None of above
Configure a client computer to use only TCP/IP for the connections to the remote access server
Configure the remote access server to allow IPX based remote access demand dial connections
Configure the remote access server to disable multi-link connection
Configure the client computer to use a defined IPX network address for the connection to the remote access servers

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network contains 10 domain controllers, 10 member servers, and approximately 1,000 client computers. All the servers run Windows 2000 Server, and all the client computers run Windows 2000 Professional. Two of the domain controllers act as DNS servers. Users of client computers use file sharing to grant access to files stored locally. The network has 10 subnets and uses TCP/IP as the only network protocol. You want to configure the network so that all computers can resolve the addresses of all other computers by using DNS. Client computers must be able to register and resolve addresses if a server fails. How should you configure the DNS servers?

Configure one server with an Active directory integrated primary zone for the domain, and configure at least one server with a standard secondary zone
Configure at least two servers with standard primary zones for the domain
Configure one server with a standard primary zone for the domain, and configure at least one server with standard secondary zone
Configure one server with a standard primary zone for the domain, and configure at least one server with an Active Directory integrated primary zone
Configure at least two servers with Active Directory integrated primary zones for the domain

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has FIVE hard disks. Four 100 GB hard disks on the server are configured as a single stripe volume. You want to reconfigure the fourth disk so that the volume is fault tolerant and has as much space possible available for storing data. You want to use only existing hardware. What should you do?

Backup the data on the stripe volume and delete the stripe volume. Create a raidS volume on the four disks, restore the data to the new raid5 volume
Convert the disk to dynamic disk shut doWn and restart the server
None of above
Backup the data on the stripe volume and delete the stripe volume. Create a mirror volume, shut down and restart the server. Restore the data to new mirror volumes
Backup the data on the stripe volume and delete the stripe

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
How can you assign an application to one processor exclusively?

None of above.
Open Task Manager, chose Performance, chose view all processors, assign processes to appropriate processor
Open Task Manager, chose options from task bar, select processor and assign processes to appropriate processor
Right click on application executable, select properties and select assign processor
Right click on application process in Task Manager, select Set Affinity, and select the appropriate processor

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server