Windows 2000 Server
You are configuring a Windows 2000 Server computer as a Routing and Remote Access server for a Branch office. You discover that an incorrect driver was installed during the installation of the modem. You attempt to remove the modem by using Phone and Modem Options in Control Panel. After each attempt to remove the modem by using this method, the computer stops responding. You restart the computer again. You must install the correct driver for the modem as quickly as possible. What should you do?

Use the Add/Remove Hardware wizard to uninstall the modem. Restart the server
Run the Modem troubleshooter and remove the modem when prompted. Restart the server
None of above
Delete all references to modems in the registry
Shut down the server, remove the modem card, and restart the server. Shut down the server again, insert the modem card, and restart the server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network contains 10 domain controllers, 10 member servers, and approximately 1,000 client computers. All the servers run Windows 2000 Server, and all the client computers run Windows 2000 Professional. Two of the domain controllers act as DNS servers. Users of client computers use file sharing to grant access to files stored locally. The network has 10 subnets and uses TCP/IP as the only network protocol. You want to configure the network so that all computers can resolve the addresses of all other computers by using DNS. Client computers must be able to register and resolve addresses if a server fails. How should you configure the DNS servers?

Configure one server with a standard primary zone for the domain, and configure at least one server with an Active Directory integrated primary zone
Configure at least two servers with Active Directory integrated primary zones for the domain
Configure at least two servers with standard primary zones for the domain
Configure one server with an Active directory integrated primary zone for the domain, and configure at least one server with a standard secondary zone
Configure one server with a standard primary zone for the domain, and configure at least one server with standard secondary zone

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are installing Windows 2000 Server on a multiprocessor computer. The manufacturer has provided a customized HAL to use with the computer. The HAL is on the floppy disk. You want to install the customized HAL design for the computer. What should you do?

After the Windows 2000 setup is complete use the device manager to scan for Hardware changes when prompted install the customized HAL
After the text mode portion your windows 2000 setup is complete use the emergency repair process to replace the existing HAL with the customized HAL and then continue the windows 2000 setup
During the text mode portion of the Windows 2000 setup install the customized HAL
None of above
After text mode portion of Windows 2000 setup is complete use the recovery console to copy the customized HAL to the system32 folder on the boot partition

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer includes an integrated 10-MB Ethernet adapter. You are replacing the integrated adapter with a new 100-MB Ethernet adapter. You install the new adapter in an available PCI slot. When you restart the computer, you receive error messages in the System log stating that the new adapter Is missing or is not working. What should you do to resolve the problem?

Use Device Manager to disable the integrated 10-MB Ethernet adapter
Create a new hardware profile
None of above
Use Device Manager to remove the integrated 10-MB Ethernet adapter
Delete the device driver for the integrated 10-MB Ethernet adapter from the Systemrootsystem32Driver Cache folder

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
None of above
Configure Engineering2 and Sales2 as DHCP servers without any scopes
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
On Engineering2 and Sales2, install and configure the DHCP Relay Agent service

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install and run a third-party 32-bit application named Application on your Windows 2000 Server computer. After several days, the application stops responding. You open Task Manager and find that the CPU usage is at 100 percent. The normal range of CPU usage on the server is from 20 percent to 30 percent You end the application. However, you see that the CPU on the server is still at 100 percent. Task Manager shows no other applications running. You then examine the Processes page in Task Manager and confirm that the Application.exe process is no longer running. You want to return the CPU usage to its normal range. What should you do?

Use Computer Management to stop and restart the Server service
None of above
Use Computer Management to stop and restart the Workstation service
Use Task Manager to end any related child processes
Use Task Manager to end and automatically restart the Explorer.exe process

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server