Windows 2000 Server
You are the administrator of a Windows 2000 domain that has three domain controllers. Each day, you use Windows Backup to perform full backups of each domain controller. You run a script to make changes to account information in Active Directory. As a result of errors in the script, the incorrect user accounts are modified. Active Directory replication then replicates the changes to the other two domain controllers. You want to revert Active Directory to the version that was backed up the previous day. What should you do?

Shut down, and restart a single domain controller by using the Recovery Console. Use Windows Backup to restore the System State data. Exit the Recovery Console. Restart the computer
On a single domain controller, use Windows Backup to restore the System State data. Shut down and restart the computer
Shut down and restart a single domain controller in directory services restore mode. Use Windows Backup to restore the System State data. Run the Ntdsutil utility. Restart the computer
Shut down and restart each domain controller by using the Recovery Console. Use Windows Backup to restore the Sysvol folder. Exit the Recovery Console. Restart the computer
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to install Windows 2000 server on 15 new computers. You want to install, configure and test all 2000 servers before shipping them to your branch offices. You want the users at the branch offices to enter the serial numbers and computer names once they receive the computers. What should you do?

Install Windows 2000 server on the computers. Use Sysprep.exe to create the Unattend.txt file, place file on the root of the drive
Create an Unattend.txt file by using Setup Manager. Create a UDF file that identifies the names of the new computers
None of above
Create a UDF file by using setup manager. Create an Unattend.txt file that identifies the names of the new computers
Install Windows 2000 server on the computers. Use Setup Manager to create a sysprep.inf file for use with sysprep.exe Place the sysprep.inf on the computers and run sysprep -noidgen

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has FIVE hard disks. Four 100 GB hard disks on the server are configured as a single stripe volume. You want to reconfigure the fourth disk so that the volume is fault tolerant and has as much space possible available for storing data. You want to use only existing hardware. What should you do?

Backup the data on the stripe volume and delete the stripe
Convert the disk to dynamic disk shut doWn and restart the server
Backup the data on the stripe volume and delete the stripe volume. Create a mirror volume, shut down and restart the server. Restore the data to new mirror volumes
Backup the data on the stripe volume and delete the stripe volume. Create a raidS volume on the four disks, restore the data to the new raid5 volume
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server to act as a DHCP Relay Agent
Configure the remote access server with the address of a DHCP server
None of above
Authorize the remote access server to receive multiple addresses from a DHCP server
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You enable the Routing and Remote Access Service (RRAS) on a computer running Windows 2000 Server. You configure the computer as a RAS server. You want to provide mutual authentication between the RAS server and RAS clients. You also want to ensure that data passing between the RAS server and RAS clients is encrypted. Which authentication method should you use for your incoming connections to support mutual authentication and data encryption?

SPAP
PAP
None of above
CHAP
MS-CHAP v2

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You configure your Windows 2000 Server as a print server. You install a second PnP Network adapter to improve the performance. The first adapter uses IRQ11, and the second adapter uses IRQ5. The server is now unable to print to print devices connected to a non-PnP LPT2 port adapter. You want to continue to use the print devices connected to your print server. What should you do?

None of above
Use device manager to change the IRQ for LPT1 to IRQ10
Use device manager to change the IRQ for LPT2 to IRQ7
Edit the CMOS setting of the servers BIOS to reserve IRQ5 for non-PnP devices
Edit the CMOS setting of the servers BIOS to reserve IRQ7 for non-PnP devices

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server