Windows 2000 Server
You are installing Windows 2000 Server on a multiprocessor computer. The manufacturer has provided a customized HAL to use with the computer. The HAL is on the floppy disk. You want to install the customized HAL design for the computer. What should you do?

After the text mode portion your windows 2000 setup is complete use the emergency repair process to replace the existing HAL with the customized HAL and then continue the windows 2000 setup
After the Windows 2000 setup is complete use the device manager to scan for Hardware changes when prompted install the customized HAL
During the text mode portion of the Windows 2000 setup install the customized HAL
After text mode portion of Windows 2000 setup is complete use the recovery console to copy the customized HAL to the system32 folder on the boot partition
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install your boot volume on volume C on your Windows 2000 Server computer. You mirror volume C on dynamic Disk 1. Two years later, during routine server maintenance, you open Disk Management and find that the status of volume C is Failed Redundancy. The status of Disk 1 is Missing. You attempt to reactivate Disk 1, but the status of volume C does not return to Healthy. What should you do next?

Replace Disk 1 and restart the computer. The mirror will automatically regenerate
Replace Disk 1 and copy all data from volume C to a new NTFS primary partition on the new Disk 1. Restart the computer
Rescan the disks, remove the mirror, and delete the data on Disk 1. Then re-create the mirror
None of above
Remove the mirror on Disk 1, replace the disk, and then add back the mirror to the new Disk 1

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You have just configured two Windows NT Servers, Monitor 1 and Monitor 2 with no other software installed. You have an application server that needs to be monitored for performance to figure out what it's problem is, or to get some kind of baseline. You install Network Monitor on Monitor 2. What would you do to monitor Application server?

Configure Monitor 2 and Application server as monitoring partners (or something) to monitor the performance
Configure the network monitor EDP port something for UDP
Install Network Monitor on Monitor 1
Configure the network monitor ECP port something for TCP
Install Network Monitor on Application Server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
On Engineering2 and Sales2, install and configure the DHCP Relay Agent service
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
None of above
Configure Engineering2 and Sales2 as DHCP servers without any scopes

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices
Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
Use Device Manager to change the IRQ for the original modem to IRQ 10
None Of above
Use Device Manager to change the IRQ for the original modem to IRQ 9

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your computer has a mirrored volume and you wish to now install the Recovery Console for future troubleshooting. How do you do this?

None of above
Run the add and remove programs and add the recovery console
Reinstall Windows, this can only be applied during the installation
Break the mirror, run X:i386winnt32.exe /cmdcons Reestablish the mirror
Run X:i386winnt32.exe / cmdcons

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server