Windows 2000 Server
You install Terminal Services on a Windows 2000 domain controller. You install Terminal Services Client on users' client computers. Users report that when they try to connect to the Terminal server, they receive the following error message: "The local policy of this system does not allow you to logon interactively." When you attempt to log on to the Terminal server as an administrator from a user's computer, you log on successfully. You want users to be able to log on to the Terminal server. What should you do?

Copy the users' prpfiles to the Terminal server
Grant the users the right to log on over the network
Grant the users the right to log on as a service
Copy the users' home folders to the Terminal server
Grant the users the right to log on locally

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to provide complete redundancy for all data stored on your hardware RAID 5 array. You install second h/w Raid 5. You want to create a mirror set of the original array. However when you right click the free space on new array you see no option to create a new volume or mirrrored volume. What should you do?

Format new disk array as a single NTFS primary partition
Create a single unformatted primary partition on new array
Convert both to dynamic disks
Format the new disk array as a single NTFS logical drive in an extended partition.
Create an empty extended partition on new disk

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
Configure Engineering2 and Sales2 as DHCP servers without any scopes
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
On Engineering2 and Sales2, install and configure the DHCP Relay Agent service
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 Server network. On each server you format a separate system partition and a separate boot partition as NTFS. Several months later you shut down one of the computers for maintenance. When you try to restart the computer you receive the following error message "NTLDR is missing, press any key to restart". You want to install a new NTLDR file on the computer but you do not want to loose any settings you made since the installation. What should you do?

Start the computer by using the Windows 2000 server CD- ROM, choose to reinstall. When the installation is complete copy the NTLDR to the root of the boot volume
Start the computer by using the Windows 2000 bootable floppy disk. From a command prompt run the sfc/scanboot command
None of above
Start the computer by using Windows 2000 bootable floppy disk. Run the file signature verification utility
Start the computer by using Windows 2000 Server computer CD-ROM and choose tools to repair the installation. Select recovery console and copy the NTLDR file on the CD-ROM to the root of the system vol

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server with the address of a DHCP server
None of above
Authorize the remote access server to receive multiple addresses from a DHCP server
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
Configure the remote access server to act as a DHCP Relay Agent

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Use Device Manager to change the IRQ for the original modem to IRQ 9
Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
None Of above
Use Device Manager to change the IRQ for the original modem to IRQ 10
Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server