Windows 2000 Server
You are a network administrator for your company. The company is currently configuring its branch offices with a Windows 2000 Server computer at each office. Each branch office has a technical-support department but not a network administrator. You want to configure the remote Windows 2000 Server computers so that whenever a new Microsoft driver becomes available, the branch offices are notified automaticaly when the administrator logs onto the server. What should you do?

Configure system file checker to notify the branch offices
None of above
Configure Windows file protection to notify the branch offices
Install Windows critical update notification
Install the Windows 2000 Resource Kit

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Use Device Manager to change the IRQ for the original modem to IRQ 9
Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
None Of above
Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices
Use Device Manager to change the IRQ for the original modem to IRQ 10

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

Configure a client computer to use only TCP/IP for the connections to the remote access server
Configure the client computer to use a defined IPX network address for the connection to the remote access servers
None of above
Configure the remote access server to allow IPX based remote access demand dial connections
Configure the remote access server to disable multi-link connection

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to provide complete redundancy for all data stored on your hardware RAID 5 array. You install second h/w Raid 5. You want to create a mirror set of the original array. However when you right click the free space on new array you see no option to create a new volume or mirrrored volume. What should you do?

Format new disk array as a single NTFS primary partition
Convert both to dynamic disks
Format the new disk array as a single NTFS logical drive in an extended partition.
Create a single unformatted primary partition on new array
Create an empty extended partition on new disk

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

None of above
Configure the remote access server with the address of a DHCP server
Authorize the remote access server to receive multiple addresses from a DHCP server
Configure the remote access server to act as a DHCP Relay Agent
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer. The server has a single hard disk with a single NTFS partition. You use a third-party tool to add a new partition to the disk. When you restart the server, you received the following error message: "Windows 2000 could not start because the following file is missing or corrupt: \system32\ntoskrnl.exe. Please re-install a copy of the above file." What should you do to resolve the problem?

Start the computer by using the Recovery Console. Run System File Checker
Start the emergency repair process. Choose the option to repair system files
None of above
Start the computer by using the Recovery Console. Modify the Partition parameter in the operating system path in C:Boot.ini
Start the computer in safe mode with command prompt. Modify the Partition parameter in the operating system path in C:boot.ini

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server