Windows 2000 Server
You configure your Windows 2000 Server as a print server. You install a second PnP Network adapter to improve the performance. The first adapter uses IRQ11, and the second adapter uses IRQ5. The server is now unable to print to print devices connected to a non-PnP LPT2 port adapter. You want to continue to use the print devices connected to your print server. What should you do?

Use device manager to change the IRQ for LPT1 to IRQ10
Edit the CMOS setting of the servers BIOS to reserve IRQ5 for non-PnP devices
Edit the CMOS setting of the servers BIOS to reserve IRQ7 for non-PnP devices
Use device manager to change the IRQ for LPT2 to IRQ7
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer. The server contains one network adapter and is a file and print server for critical company resources. You install a second network adpater in the server and connect it to the same network subnet as the first adapter. You want to ensure that the first adapter is used for all network traffic and the second adapter is used only if the first adapter fails or is disconnected from the network. You also want to ensure that the server always has network connectivity even if one network adapter fails. What should you do?

Set the second adapters status to disable
Configure the first adapter to use a TCP/IP metric of 100
Configure the second adapter to use a TCP/IP metric of 25
None of above
Configure the binding order on the second adapter to bind TCP/IP last

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
None of above
Configure Engineering2 and Sales2 as DHCP servers without any scopes
On Engineering2 and Sales2, install and configure the DHCP Relay Agent service

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 server Computer contains data files that users of client computers access throughout the day. You install a driver for the new tape drive on the computer. After restarting the computer you log on as an administrator, shortly after you log on you receive the following stop error "irql_not_less_6r_equal". You need to bring the server back on line as quickly and reliably as possible. What should you do?

Restart the computer in the safe mode, remove the driver and restart the computer
Perform an emergency repair and select fast repair, restart the computer
Restart the computer by using the recovery console, disable the driver. Restart the computer, remove the driver
None of above
Restart the computer by using the last known good menu option

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to provide complete redundancy for all data stored on your hardware RAID 5 array. You install second h/w Raid 5. You want to create a mirror set of the original array. However when you right click the free space on new array you see no option to create a new volume or mirrrored volume. What should you do?

Convert both to dynamic disks
Format the new disk array as a single NTFS logical drive in an extended partition.
Create an empty extended partition on new disk
Create a single unformatted primary partition on new array
Format new disk array as a single NTFS primary partition

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 Server network. On each server you format a separate system partition and a separate boot partition as NTFS. Several months later you shut down one of the computers for maintenance. When you try to restart the computer you receive the following error message "NTLDR is missing, press any key to restart". You want to install a new NTLDR file on the computer but you do not want to loose any settings you made since the installation. What should you do?

Start the computer by using Windows 2000 Server computer CD-ROM and choose tools to repair the installation. Select recovery console and copy the NTLDR file on the CD-ROM to the root of the system vol
None of above
Start the computer by using the Windows 2000 bootable floppy disk. From a command prompt run the sfc/scanboot command
Start the computer by using Windows 2000 bootable floppy disk. Run the file signature verification utility
Start the computer by using the Windows 2000 server CD- ROM, choose to reinstall. When the installation is complete copy the NTLDR to the root of the boot volume

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server