Windows 2000 Server
You are the administrator of a network that consists of a single Windows NT 4.0 domain. The network contains five Windows NT Server domain controllers and 1,000 Windows NT Workstation client computers. You want to install Windows 2000 Server on a new computer. You want the new computer to act as a domain controller in the existing domain. What should you do?

Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory Installation wizard to install Active Director
Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory Installation wizard to install Active Director
None of above
On the new computer, install Windows NT Server 4.0 and designate the computer as a BDC in the existing domain. Promote the computer to the PDC of the domain. Upgrade the computer to Windows 2000 Serve
On the new computer, install Windows NT Server 4.0 and designate the computer as a PDC in a new domain that has the same NetBIOS name as the existing Windows NT domain. Upgrade the computer to Windows

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are configuring a Windows 2000 Server computer as a Routing and Remote Access server for a Branch office. You discover that an incorrect driver was installed during the installation of the modem. You attempt to remove the modem by using Phone and Modem Options in Control Panel. After each attempt to remove the modem by using this method, the computer stops responding. You restart the computer again. You must install the correct driver for the modem as quickly as possible. What should you do?

Delete all references to modems in the registry
Use the Add/Remove Hardware wizard to uninstall the modem. Restart the server
None of above
Shut down the server, remove the modem card, and restart the server. Shut down the server again, insert the modem card, and restart the server
Run the Modem troubleshooter and remove the modem when prompted. Restart the server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install Terminal Services on a Windows 2000 domain controller. You install Terminal Services Client on users' client computers. Users report that when they try to connect to the Terminal server, they receive the following error message: "The local policy of this system does not allow you to logon interactively." When you attempt to log on to the Terminal server as an administrator from a user's computer, you log on successfully. You want users to be able to log on to the Terminal server. What should you do?

Copy the users' prpfiles to the Terminal server
Grant the users the right to log on over the network
Copy the users' home folders to the Terminal server
Grant the users the right to log on as a service
Grant the users the right to log on locally

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You have just configured two Windows NT Servers, Monitor 1 and Monitor 2 with no other software installed. You have an application server that needs to be monitored for performance to figure out what it's problem is, or to get some kind of baseline. You install Network Monitor on Monitor 2. What would you do to monitor Application server?

Configure the network monitor ECP port something for TCP
Install Network Monitor on Monitor 1
Configure the network monitor EDP port something for UDP
Configure Monitor 2 and Application server as monitoring partners (or something) to monitor the performance
Install Network Monitor on Application Server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

None of above
Configure Engineering2 and Sales2 as DHCP servers without any scopes
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
On Engineering2 and Sales2, install and configure the DHCP Relay Agent service
Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has one hard disk. This computer runs a custom application that writes a large number of small temporary files in a single directory to support request from client computers. To improve performance of the application, you add three new 100-GB SCSI disks to the server to hold these temporary files. You want to ensure that the application can use all 300 GB of space with a single drive letter. You also want to ensure the fastest possible performance when writing the temporary files. How should you configure the three disks?

Create a single volume on each of the three disks. Format each volume as NTFS. Mount the roots of Disk 2 and Disk 3 in the root folder of Disk 1
None of above
Create a single volume on Disk 1. Format the volume as NTFS. Extend the volume to create a spanned volume that includes the space on all three disks
Convert all three disks to dynamic disks. Create a RAID-5 volume
Convert all three disks to dynamic disks. Create a striped volume

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server