Windows 2000 Server
The network uses TCP/IP as the only network protocol. You configure the remote access server on the network. Some users report that when they connect to the server they receive the following message |" IPX SPX compatible computer deported error 733" The EPP control network protocol for the network is not available. If the users allow the connection to continue they are able to connect to the services that use TCP/IP. You want to prevent this message from being displayed. What should you do?

None of above
Configure the remote access server to disable multi-link connection
Configure the remote access server to allow IPX based remote access demand dial connections
Configure a client computer to use only TCP/IP for the connections to the remote access server
Configure the client computer to use a defined IPX network address for the connection to the remote access servers

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You enable the Routing and Remote Access Service (RRAS) on a computer running Windows 2000 Server. You configure the computer as a RAS server. You want to provide mutual authentication between the RAS server and RAS clients. You also want to ensure that data passing between the RAS server and RAS clients is encrypted. Which authentication method should you use for your incoming connections to support mutual authentication and data encryption?

MS-CHAP v2
PAP
SPAP
CHAP
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install your boot volume on volume C on your Windows 2000 Server computer. You mirror volume C on dynamic Disk 1. Two years later, during routine server maintenance, you open Disk Management and find that the status of volume C is Failed Redundancy. The status of Disk 1 is Missing. You attempt to reactivate Disk 1, but the status of volume C does not return to Healthy. What should you do next?

Replace Disk 1 and restart the computer. The mirror will automatically regenerate
Replace Disk 1 and copy all data from volume C to a new NTFS primary partition on the new Disk 1. Restart the computer
Remove the mirror on Disk 1, replace the disk, and then add back the mirror to the new Disk 1
None of above
Rescan the disks, remove the mirror, and delete the data on Disk 1. Then re-create the mirror

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are configuring a Windows 2000 Server computer as a Routing and Remote Access server for a Branch office. You discover that an incorrect driver was installed during the installation of the modem. You attempt to remove the modem by using Phone and Modem Options in Control Panel. After each attempt to remove the modem by using this method, the computer stops responding. You restart the computer again. You must install the correct driver for the modem as quickly as possible. What should you do?

None of above
Delete all references to modems in the registry
Use the Add/Remove Hardware wizard to uninstall the modem. Restart the server
Run the Modem troubleshooter and remove the modem when prompted. Restart the server
Shut down the server, remove the modem card, and restart the server. Shut down the server again, insert the modem card, and restart the server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
How can you assign an application to one processor exclusively?

Open Task Manager, chose Performance, chose view all processors, assign processes to appropriate processor
Open Task Manager, chose options from task bar, select processor and assign processes to appropriate processor
Right click on application executable, select properties and select assign processor
None of above.
Right click on application process in Task Manager, select Set Affinity, and select the appropriate processor

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to provide complete redundancy for all data stored on your hardware RAID 5 array. You install second h/w Raid 5. You want to create a mirror set of the original array. However when you right click the free space on new array you see no option to create a new volume or mirrrored volume. What should you do?

Format new disk array as a single NTFS primary partition
Create a single unformatted primary partition on new array
Format the new disk array as a single NTFS logical drive in an extended partition.
Convert both to dynamic disks
Create an empty extended partition on new disk

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server