Windows 2000 Server
You are the administrator of Windows 2000 Server network. On each server you format a separate system partition and a separate boot partition as NTFS. Several months later you shut down one of the computers for maintenance. When you try to restart the computer you receive the following error message "NTLDR is missing, press any key to restart". You want to install a new NTLDR file on the computer but you do not want to loose any settings you made since the installation. What should you do?

None of above
Start the computer by using Windows 2000 bootable floppy disk. Run the file signature verification utility
Start the computer by using Windows 2000 Server computer CD-ROM and choose tools to repair the installation. Select recovery console and copy the NTLDR file on the CD-ROM to the root of the system vol
Start the computer by using the Windows 2000 server CD- ROM, choose to reinstall. When the installation is complete copy the NTLDR to the root of the boot volume
Start the computer by using the Windows 2000 bootable floppy disk. From a command prompt run the sfc/scanboot command

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of Windows 2000 domain and TWO Windows NT domains. The Windows 2000 domains trust each of the Windows NT domains. Each of Windows NT domains trust the Windows 2000 domain. A Windows 2000 domain controller named DC1 is configured to use a highly secure domain controller template. Users in the Windows NT domain report that they cannot access DC1. You need to allow the users of computers in the Windows NT domain to access resources on DC1. What should you do?

Ensure the Windows 2000 domain is configured in the mixed mode
Apply a less restrictive custom security template to DC1
Ensure the Windows 2000 domain is configured to run in the native mode
None of above
Apply a less restrictive custom policy to Windows NT domain controller

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
Use Device Manager to change the IRQ for the original modem to IRQ 10
Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices
None Of above
Use Device Manager to change the IRQ for the original modem to IRQ 9

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server to act as a DHCP Relay Agent
None of above
Authorize the remote access server to receive multiple addresses from a DHCP server
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
Configure the remote access server with the address of a DHCP server

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has FIVE hard disks. Four 100 GB hard disks on the server are configured as a single stripe volume. You want to reconfigure the fourth disk so that the volume is fault tolerant and has as much space possible available for storing data. You want to use only existing hardware. What should you do?

Backup the data on the stripe volume and delete the stripe volume. Create a raidS volume on the four disks, restore the data to the new raid5 volume
Backup the data on the stripe volume and delete the stripe
None of above
Convert the disk to dynamic disk shut doWn and restart the server
Backup the data on the stripe volume and delete the stripe volume. Create a mirror volume, shut down and restart the server. Restore the data to new mirror volumes

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer includes an integrated 10-MB Ethernet adapter. You are replacing the integrated adapter with a new 100-MB Ethernet adapter. You install the new adapter in an available PCI slot. When you restart the computer, you receive error messages in the System log stating that the new adapter Is missing or is not working. What should you do to resolve the problem?

Create a new hardware profile
Delete the device driver for the integrated 10-MB Ethernet adapter from the Systemrootsystem32Driver Cache folder
Use Device Manager to remove the integrated 10-MB Ethernet adapter
Use Device Manager to disable the integrated 10-MB Ethernet adapter
None of above

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server