Windows 2000 Server
Your Windows 2000 server Computer contains data files that users of client computers access throughout the day. You install a driver for the new tape drive on the computer. After restarting the computer you log on as an administrator, shortly after you log on you receive the following stop error "irql_not_less_6r_equal". You need to bring the server back on line as quickly and reliably as possible. What should you do?

None of above
Restart the computer by using the recovery console, disable the driver. Restart the computer, remove the driver
Restart the computer in the safe mode, remove the driver and restart the computer
Perform an emergency repair and select fast repair, restart the computer
Restart the computer by using the last known good menu option

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer contains a stripe set with parity on a four-disk array. You convert the stripe set with parity to a dynamic RAID-5 volume. Six months later, users report that disk access on the server is slower than it had been on the previous day, You use Disk Management and discover that the status of the third disk in the array is Missing. You want to recover the failed RAID-5 volume. What should you do first?

Ensure that the third disk is attached to the server and has power. Use Disk Management to reactivate the disk
None of above
Replace the third disk and restart the server. Use disk Management to repair the volume
Install a new disk and create a single extended partition on the new disk. Restart the computer and allow Windows 2000 to automatically repair the volume on the extended partition
Ensure that the third disk is attached to the server and has power. Use Disk Management to repair the volume

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a network that consists of a single Windows NT 4.0 domain. The network contains five Windows NT Server domain controllers and 1,000 Windows NT Workstation client computers. You want to install Windows 2000 Server on a new computer. You want the new computer to act as a domain controller in the existing domain. What should you do?

None of above
On the new computer, install Windows NT Server 4.0 and designate the computer as a PDC in a new domain that has the same NetBIOS name as the existing Windows NT domain. Upgrade the computer to Windows
Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory Installation wizard to install Active Director
On the new computer, install Windows NT Server 4.0 and designate the computer as a BDC in the existing domain. Promote the computer to the PDC of the domain. Upgrade the computer to Windows 2000 Serve
Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory Installation wizard to install Active Director

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to install Windows 2000 server on 15 new computers. You want to install, configure and test all 2000 servers before shipping them to your branch offices. You want the users at the branch offices to enter the serial numbers and computer names once they receive the computers. What should you do?

None of above
Install Windows 2000 server on the computers. Use Setup Manager to create a sysprep.inf file for use with sysprep.exe Place the sysprep.inf on the computers and run sysprep -noidgen
Create an Unattend.txt file by using Setup Manager. Create a UDF file that identifies the names of the new computers
Create a UDF file by using setup manager. Create an Unattend.txt file that identifies the names of the new computers
Install Windows 2000 server on the computers. Use Sysprep.exe to create the Unattend.txt file, place file on the root of the drive

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Authorize the remote access server to receive multiple addresses from a DHCP server
Configure the remote access server to act as a DHCP Relay Agent
Configure the remote access server with the address of a DHCP server
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You want to provide Internet access for the clients on your network. You decide to use Network Address Translation (NAT). You have a Windows 2000 computer you try to establish a secure Virtual Private Networking session with. You try connecting to the Remote Windows 2000 computer using L2TP. You are unable to establish a connection with the remote node using L2TP. You are able to make a connection with another computer in your same office. Why are you unable to make a connection.to the remote location?

L2TP does not work with Windows 2000 computers
You can not establish a L2TP connection behind a computer running NAT. The L2TP session fails because the IP Security packets become corrupted
NAT does not allow for remote networking
None of above
You have not configured the NAT server to translate the IP Security packets

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server