A single phase load is connected between R and Y terminals of a 415 V, symmetrical, 3-phase, 4 wire system with phase sequence RYB. A wattmeter is connected in the system as shown in figure. The power factor of the load is 0.8 lagging. The wattmeter will read

Measurement and Instrumentation
A single phase load is connected between R and Y terminals of a 415 V, symmetrical, 3-phase, 4 wire system with phase sequence RYB. A wattmeter is connected in the system as shown in figure. The power factor of the load is 0.8 lagging. The wattmeter will read

+ 795 W.

- 597 W.

- 795 W.

+ 597 W.

+ 795 W.

- 597 W.

- 795 W.

+ 597 W.

ANSWER DOWNLOAD EXAMIANS APP

Measurement and Instrumentation
A sinusoidal signal waveform, when observed on an oscilloscope, has a peak to peak amplitude of 6 cm. If the vertical sensitivity setting is 5 v/cm, then rms value of the voltage will be

15 V.

11.1 V.

10.6 V.

12.6 V.

15 V.

11.1 V.

10.6 V.

12.6 V.

ANSWER DOWNLOAD EXAMIANS APP

Measurement and Instrumentation
The limiting errors of measurement of power consumed by and the current passing through a resistance are ±1.5% and ±1% respectively. What is the limiting error ( in %) of measurement of resistance ?

±3.5%

± 1.5%

± 1%

± 2.5%

±3.5%

± 1.5%

± 1%

± 2.5%

ANSWER DOWNLOAD EXAMIANS APP

Measurement and Instrumentation
For measurement of mutual inductance we can use

Any of the listed here

Maxwell's bridge

Heavyside bridge

Anderson bridge

Any of the listed here

Maxwell's bridge

Heavyside bridge

Anderson bridge

ANSWER DOWNLOAD EXAMIANS APP

Measurement and Instrumentation
Why is a MISC meter not recommended for DC measurement?

The error is high due to eddy current effect

The meter does not respond to DC signals

The meter is calibrated for AC and it’s error for DC would be high

The error is high due to hysteresis effect

The error is high due to eddy current effect

The meter does not respond to DC signals

The meter is calibrated for AC and it’s error for DC would be high

The error is high due to hysteresis effect

ANSWER DOWNLOAD EXAMIANS APP

Measurement and Instrumentation
Standardization of potentiometer is done in order that, they become

accurate and direct reading.

accurate.

accurate and precise.

precise.

accurate and direct reading.

accurate.

accurate and precise.

precise.

ANSWER DOWNLOAD EXAMIANS APP

Measurement and Instrumentation

Measurement and Instrumentation A single phase load is connected between R and Y terminals of a 415 V, symmetrical, 3-phase, 4 wire system with phase sequence RYB. A wattmeter is connected in the system as shown in figure. The power factor of the load is 0.8 lagging. The wattmeter will read

Measurement and Instrumentation A sinusoidal signal waveform, when observed on an oscilloscope, has a peak to peak amplitude of 6 cm. If the vertical sensitivity setting is 5 v/cm, then rms value of the voltage will be

Measurement and Instrumentation The limiting errors of measurement of power consumed by and the current passing through a resistance are ±1.5% and ±1% respectively. What is the limiting error ( in %) of measurement of resistance ?

Measurement and Instrumentation For measurement of mutual inductance we can use

Measurement and Instrumentation Why is a MISC meter not recommended for DC measurement?

Measurement and Instrumentation Standardization of potentiometer is done in order that, they become

Measurement and Instrumentation
A single phase load is connected between R and Y terminals of a 415 V, symmetrical, 3-phase, 4 wire system with phase sequence RYB. A wattmeter is connected in the system as shown in figure. The power factor of the load is 0.8 lagging. The wattmeter will read

Measurement and Instrumentation
A sinusoidal signal waveform, when observed on an oscilloscope, has a peak to peak amplitude of 6 cm. If the vertical sensitivity setting is 5 v/cm, then rms value of the voltage will be

Measurement and Instrumentation
The limiting errors of measurement of power consumed by and the current passing through a resistance are ±1.5% and ±1% respectively. What is the limiting error ( in %) of measurement of resistance ?

Measurement and Instrumentation
For measurement of mutual inductance we can use

Measurement and Instrumentation
Why is a MISC meter not recommended for DC measurement?

Measurement and Instrumentation
Standardization of potentiometer is done in order that, they become