Windows 2000 Server
Your computer has a mirrored volume and you wish to now install the Recovery Console for future troubleshooting. How do you do this?

Run X:i386winnt32.exe / cmdcons
None of above
Reinstall Windows, this can only be applied during the installation
Break the mirror, run X:i386winnt32.exe /cmdcons Reestablish the mirror
Run the add and remove programs and add the recovery console

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Authorize the remote access server to receive multiple addresses from a DHCP server
None of above
Configure the remote access server to act as a DHCP Relay Agent
Configure the remote access server with the address of a DHCP server
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer. The server contains one network adapter and is a file and print server for critical company resources. You install a second network adpater in the server and connect it to the same network subnet as the first adapter. You want to ensure that the first adapter is used for all network traffic and the second adapter is used only if the first adapter fails or is disconnected from the network. You also want to ensure that the server always has network connectivity even if one network adapter fails. What should you do?

Set the second adapters status to disable
Configure the binding order on the second adapter to bind TCP/IP last
None of above
Configure the first adapter to use a TCP/IP metric of 100
Configure the second adapter to use a TCP/IP metric of 25

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are installing Windows 2000 Server on a multiprocessor computer. The manufacturer has provided a customized HAL to use with the computer. The HAL is on the floppy disk. You want to install the customized HAL design for the computer. What should you do?

After the Windows 2000 setup is complete use the device manager to scan for Hardware changes when prompted install the customized HAL
After the text mode portion your windows 2000 setup is complete use the emergency repair process to replace the existing HAL with the customized HAL and then continue the windows 2000 setup
After text mode portion of Windows 2000 setup is complete use the recovery console to copy the customized HAL to the system32 folder on the boot partition
None of above
During the text mode portion of the Windows 2000 setup install the customized HAL

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer uses a non-Plug and Play ISA modem configured to use IRQ 5. You add a PCI modem and restart the computer. Device Manager reports an IRQ conflict between the two modems. Both modem are trying to use IRQ 5. You want to resolve the problem. What should you do?

Edit the CMOS settings on the computer to reserve IRQ 5 for non-Plug and Play devices
None Of above
Use Device Manager to change the IRQ for the original modem to IRQ 10
Use Device Manager to change the IRQ for the original modem to IRQ 9
Edit the CMOS settings on the computer to reserve IRQ 10 for non-Plug and Play devices

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of your company's network. You are configuring the security policy for a group of users in the finance organizational unit (OU). You need to configure a group policy so that future changes to group policy will be applied within 15 minutes to any computers that are log on to the network. What should you do?

Enable the asynchronous group policy application settings
None of above
Enable and configure the group policy refresh interval for domain controller
Enable the background refresh settings to use the default group policy refresh date
Enable and configure the group policy refresh interval for computers

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server