Windows 2000 Server
You are the network administrator for your company. Mike Nash is a member of the Administration group, and Nate Sun is a member of the Intern group. Both groups are in the same domain. On the intranet server, the Administration group is placed in the Security group, and the Intern group is placed in the Nonsecurity group. The Security group is then granted Full Control permission for the Sales virtual directory. Nate needs to update new sales information that is located on the Sales virtual directory. What should you do so that Nate can perform this task?

None of above
Make Nate a member of the Security group
Remove Nate fmm the Intern group
Enable Anonymous access for the intranet server
Enable Anonymous access for the Sales virtual directory

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Five Lakes Publishing has a Windows 2000 network serving 200 users. A server named User_srv is used to hold users' files. User_srv is configured with a single, large NTFS volume. Every user has a home folder on User_srv. Users can also use a shared folder named IN_PROGRESS to store files for books that are being prepared. The network administrator at Five Lakes Publishing configured disk quotas for the NTFS volume on User_srv. All users have a default limit of 100 MB, and the option to deny space to users who exceed their limit has been enabled. When a user named Amy Jones attempts to save a chapter of a new book to her home folder on the server, she receives the following error message: "The disk is full or too many files are open." What should Amy do to allow this document to be saved?

Move some of the files from her home folder to the IN_PROGRESS shared folder
Change the security setting of some of the files in her home folder to grant Full Control permission to a user who has not reached the quota level
Compress the files in her home folder to save disk space
None of above
Remove files from her home folder until the total uncompressed file size is less than 100 MB

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You have just configured two Windows NT Servers, Monitor 1 and Monitor 2 with no other software installed. You have an application server that needs to be monitored for performance to figure out what it's problem is, or to get some kind of baseline. You install Network Monitor on Monitor 2. What would you do to monitor Application server?

Configure Monitor 2 and Application server as monitoring partners (or something) to monitor the performance
Configure the network monitor EDP port something for UDP
Install Network Monitor on Application Server
Install Network Monitor on Monitor 1
Configure the network monitor ECP port something for TCP

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network is configured as shown in the exhibit. "Engineering! and Salesl have DHCP installed up them." All the servers are Windows 2000 Server computers that use TCP/IP as the only network protocol. The sales department uses one subnet and has servers named Salesl and Sales2. The engineering department uses another subnet and has servers named Engineeringl and Engineering2. Salesl and Engineeringl are configured to act as DHCP servers. The router that joins the two subnets is not RFC 1542 compliant and does not support DHCP/BOOTP relay. You want to allow Salesl and Engineeringl to support client computers on each other's subnets. What should you do?

Configure Engineering2 and Sales2 as DHCP servers without any scopes
On Engineering2 and Sales2, install Routing and Remote Access, and configure RIP as a routing protocol
On Engineering2 and Sales2, install and configure the DHCP Relay Agent service
Set the router option in the DHCP Scopes to 192.168.2.1 for Engineeringl and 192.168.1.1 for Salesl
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer that has FIVE hard disks. Four 100 GB hard disks on the server are configured as a single stripe volume. You want to reconfigure the fourth disk so that the volume is fault tolerant and has as much space possible available for storing data. You want to use only existing hardware. What should you do?

Backup the data on the stripe volume and delete the stripe volume. Create a mirror volume, shut down and restart the server. Restore the data to new mirror volumes
Convert the disk to dynamic disk shut doWn and restart the server
Backup the data on the stripe volume and delete the stripe volume. Create a raidS volume on the four disks, restore the data to the new raid5 volume
Backup the data on the stripe volume and delete the stripe
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer includes an integrated 10-MB Ethernet adapter. You are replacing the integrated adapter with a new 100-MB Ethernet adapter. You install the new adapter in an available PCI slot. When you restart the computer, you receive error messages in the System log stating that the new adapter Is missing or is not working. What should you do to resolve the problem?

None of above
Delete the device driver for the integrated 10-MB Ethernet adapter from the Systemrootsystem32Driver Cache folder
Use Device Manager to remove the integrated 10-MB Ethernet adapter
Create a new hardware profile
Use Device Manager to disable the integrated 10-MB Ethernet adapter

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server