A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

Computer Networking
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

IGRP has a faster update timer.

RIP has a higher metric value for that route.

The IGRP route has fewer hops.

IGRP has a lower administrative distance.

IGRP has a faster update timer.

RIP has a higher metric value for that route.

The IGRP route has fewer hops.

IGRP has a lower administrative distance.

ANSWER DOWNLOAD EXAMIANS APP

Computer Networking
What command will display the line, protocol, DLCI, and LMI information of an interface?

show run

show interface

show frame-relay pvc

sh pvc

show run

show interface

show frame-relay pvc

sh pvc

ANSWER DOWNLOAD EXAMIANS APP

Computer Networking
Which command is used to determine if an IP access list is enabled on a particular interface?

show ip interface

show interface

show access-lists

show interface access-lists

show ip interface

show interface

show access-lists

show interface access-lists

ANSWER DOWNLOAD EXAMIANS APP

Computer Networking
Which of the following network access standard is used for connecting stations to a packet-switched network?

X.21

X.75

X.25

None of these

X.3

X.21

X.75

X.25

None of these

X.3

ANSWER DOWNLOAD EXAMIANS APP

Computer Networking
An error detecting code is which code is the remainder resulting from dividing the bits to be checked by a predetermined binary number, is known as

Cyclic redundancy check

Checksum

Error rate

None of these

Error detecting code

Cyclic redundancy check

Checksum

Error rate

None of these

Error detecting code

ANSWER DOWNLOAD EXAMIANS APP

Computer Networking
You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?

Router(config-if)# encapsulation frame-relay cisco

Router(config-if)# encapsulation frame-relay ansi

Router(config-if)# encapsulation frame-relay q933a

Router(config-if)# encapsulation frame-relay ietf

Router(config-if)# encapsulation frame-relay cisco

Router(config-if)# encapsulation frame-relay ansi

Router(config-if)# encapsulation frame-relay q933a

Router(config-if)# encapsulation frame-relay ietf

ANSWER DOWNLOAD EXAMIANS APP

Computer Networking

Computer Networking A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

Computer Networking What command will display the line, protocol, DLCI, and LMI information of an interface?

Computer Networking Which command is used to determine if an IP access list is enabled on a particular interface?

Computer Networking Which of the following network access standard is used for connecting stations to a packet-switched network?

Computer Networking An error detecting code is which code is the remainder resulting from dividing the bits to be checked by a predetermined binary number, is known as

Computer Networking You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?

Computer Networking
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?

Computer Networking
What command will display the line, protocol, DLCI, and LMI information of an interface?

Computer Networking
Which command is used to determine if an IP access list is enabled on a particular interface?

Computer Networking
Which of the following network access standard is used for connecting stations to a packet-switched network?

Computer Networking
An error detecting code is which code is the remainder resulting from dividing the bits to be checked by a predetermined binary number, is known as

Computer Networking
You need to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface of the router for this connection?