Windows 2000 Server
You are the administrator of a network that consists of Windows 2000 Server computers and Windows 2000 Professional computers. You want to configure the deployment of the most recent Windows 2000 service pack so that users of the Windows 2000 Professional computers receive the service pack automatically when they log on to the domain. What should you do?

None of above
Create a Microsoft Windows installer package for the service pack. Configure RIS to use the package
Create a Microsoft -Windows Installer package for the service pack. Configure the package in the Local Computer Policy
Place the service pack in a Distributed file system (Dfs)
Create a Microsoft Windows Installer package for the service pack. Configure the package in a Group Policy

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your Windows 2000 Server computer contains a stripe set with parity on a four-disk array. You convert the stripe set with parity to a dynamic RAID-5 volume. Six months later, users report that disk access on the server is slower than it had been on the previous day, You use Disk Management and discover that the status of the third disk in the array is Missing. You want to recover the failed RAID-5 volume. What should you do first?

Install a new disk and create a single extended partition on the new disk. Restart the computer and allow Windows 2000 to automatically repair the volume on the extended partition
Ensure that the third disk is attached to the server and has power. Use Disk Management to reactivate the disk
None of above
Ensure that the third disk is attached to the server and has power. Use Disk Management to repair the volume
Replace the third disk and restart the server. Use disk Management to repair the volume

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You are the administrator of a Windows 2000 Server computer. You configure the server to audit all access to files that are places in shared folders. One week after you configured the server, users report that the server has stopped responding. You investigate the problem and discover a stop error with the error message: Stop C0000244 (Audit Failed) An attempt to generate a security audit failed. You restart the computer. You need to ensure that you can keep a record of all files access on the server. You also need to ensure that the stop error will not occur again.

Increase the size of the security log
Delete the Liscense Trial registry key
Set the Security Log to overwrite events as needed
Set the CrashonAuditFail registry key to 0
Save the security log to a file, and clear it every morning

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
Your network consists of Windows 2000 file servers, Windows 2000 print servers, Windows 2000 professional computers, Windows 2000 file servers. You must prevent any unsigned drivers from being installed on any computer in your Windows 2000 network. What should you do?

Configure a Group policy for the Default Domain Controller to block all unsigned drivers
Configure a Group policy for the Domain that blocks all unsigned drivers
None of above
Configure the Windows 2000 file servers, Windows 2000 print servers, Windows 2000 professional computers and Windows 2000 file servers to block unsigned drivers
Do nothing, this is the default setting

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You install the Routing and Remote Access service on a Windows 2000 Server computer in your network. Your network is not directly connected to the Internet and uses the private IP address range 192.168.0.0. When you use Routing and Remote Access to dial in to the server, your computer connects successfully, but you are unable to access any resources. When you try to piiig servers by using their IP addresses, you receive the following message: "Request timed out." When you run the ipconfig command, it shows that your dial-up connection has been given the IP address 169.254.75.182. What should you do to resolve the problem?

Configure the remote access server with the address of a DHCP server
Authorize the remote access server to receive multiple addresses from a DHCP server
Configure the remote access server to act as a DHCP Relay Agent
Ensure that the remote access server is able to connect to a DHCP server that has a scope for its subnet
None of above

ANSWER DOWNLOAD EXAMIANS APP

Windows 2000 Server
You configure your Windows 2000 Server as a print server. You install a second PnP Network adapter to improve the performance. The first adapter uses IRQ11, and the second adapter uses IRQ5. The server is now unable to print to print devices connected to a non-PnP LPT2 port adapter. You want to continue to use the print devices connected to your print server. What should you do?

Use device manager to change the IRQ for LPT2 to IRQ7
Use device manager to change the IRQ for LPT1 to IRQ10
None of above
Edit the CMOS setting of the servers BIOS to reserve IRQ7 for non-PnP devices
Edit the CMOS setting of the servers BIOS to reserve IRQ5 for non-PnP devices

ANSWER DOWNLOAD EXAMIANS APP
MORE MCQ ON Windows 2000 Server